Inovance Driver

Short Description:

Thank you for purchasing the IS580 series servo drive developed and manufactured by Inovance. The IS580 is an upgrade product compared with the IS300 series servo drive. It is specially designed to drive the permanent magnet synchronous motor (PMSM) and implement high-performance vector control of the PMSM. By integrating the process control during driving of the injection molding machine (IMM), such as precise control of injection speed and pressure holding, and stability control during coo...


Product Detail

Product Tags

Thank you for purchasing the IS580 series servo drive developed and manufactured by Inovance.
The IS580 is an upgrade product compared with the IS300 series servo drive. It is specially designed to drive the
permanent magnet synchronous motor (PMSM) and implement high-performance vector control of the PMSM. By integrating the process control during driving of the injection molding machine (IMM), such as precise control of injection speed and pressure holding, and stability control during cooperation with the IMM controller, the IS580 can
well control the servo pump and provide general-purpose servo functions. The IS580 is highly cost-effective and reliable. It has obvious energy saving effect compared with traditional IMM control mode.
It is applicable to plastic molding, pipe extrusion, shoe making, rubber producing, and metal casting. Compared with the IS300, the IS580 features better oil pressure control performance, faster pressure and speed response,smaller steady pressure fluctuation and smaller size.
This manual is a guideline for the selection, installation, parameter setting, on-site commissioning and troubleshooting of the IS580 servo drive. It is only applicable to the IS580****-**-1 series servo drives.
Before using the servo drive, read this manual carefully to have a thorough understanding of the product. Keep the manual well and forward it to end users with the product.
99
Note
The drawings in the manual are sometimes shown without covers or protective guards. Remember to install the covers or protective guards as specified first, and then perform operations in accordance with the instructions.
The drawings in the manual are shown for description only and may not match the product you purchased.
The instructions are subject to change, without notice, due to product upgrade, specificationmodification as well as efforts to increase the accuracy and convenience of the manual.
Contact our agents or customer service center if you have any problem during the use.
Introduction
■ Advantages
Compared with the IS300, the IS580 has improvements in the following aspects:

Improvement Description
More stable pressure The pressure fluctuation is smaller. The stability obvious at high pressure and low speed.
Faster pressure and speed response The pressure and speed responsiveness improves, satisfying the quick response requirements of the quick hydraulic IMM.
Higher injection molding product consistency The IS580 sees a rise in the qualified rate of the injection moudling products, especially the
quick injection molding products.
Smaller size The IS580 is over 40% smaller than the IS300 for the same power class.
Wide voltage range design Rated voltage input: 380 to 480 V, wide voltage range: 323 to 528 V
Built-in DC reactor The IS580 of 30 kW and above have built-in DC reactor.
Built-in braking unit and related protective function

The power class of the IS580 with built-in braking unit extends to 75 kW (optional for the models of 90 kW above). The protective functions including braking resistor short-circuit, braking circuit overcurrent, brake pipe overload and brake pipe shoot-through.

Longer serving life The bus capacitor has high disposition and long servicing life.
Cooling fan drive circuit protection When short-circuit occurs on the cooling fan, the cooling fan drive circuit provides protection.
Complete protective functions The whole series of IS580 drives have the protections on short-circuit to ground and pre- charge relay (contactor) close fault.
Complete EMC solution Complete EMC solution (including optional EMI filter, common mode rejector / zero-phase reactor and simple filter) could be provided to satisfy the actual application and certification requirements.

Product Checking Upon unpacking, check:

  • Whether the nameplate model and the drive ratings are consistent with your order. The box contains the servo

drive, certificate of conformity, user manual and warranty card.

  • Whether the servo drive is damaged during transportation. If you find any omission or damage, contact Inovance or your supplier immediately.

First-time Use
For the users who use this product for the first time, read the manual carefully. If you have any problem concerning
the functions or performance, contact the technical support personnel of Inovance to ensure correct use.
Standard Compliant
The IS580 series servo drive complies with the international standards listed in the following table.

Directive Directive Code Standard
EMC directive 2004/108/EC EN 61800-3
EN 55011
EN 61000-6-2
LVD directive 2006/95/EC
93/68/EEC
EN 61800-5-1

The IS580 series servo drive complies with the requirements of standard IEC/EN 61800-3 on the condition of
correct installation and use by following the instructions in sections 8.3.2 and 8.3.5.
88888


  • Previous:
  • Next:

  • Related Products